Page 1 of 1

Guy Croft 3D Exhaust cam needed for Vintage build

Posted: Fri Dec 14, 2018 12:14 am
by ST3Racer
I need a GC 3D Exhaust cam for a race engine build. Any one out there know where I can get one in the USA? I have purchased from Guy in England but would like to use a USA source, if possible. Any help? PM me or reply to this thread. I have also posted into the Wanted Forum.

I have other racing goodies to trade for this - such as a GC 4A racing cam (inlet or exhaust, I have both), SERRA S1 46/86-86/46, 12.19 gross lift cam that will go either side, various really good street cams, some billets (Breda, PBS), and some regrinds (Delta), 2 complete Electromotive Crank-Fire set-ups for late 1756, and 1995 TC engines, with the damper, toothed wheel, sensor bracket, and processors, all ready to bolt on. Plus more - just ask. Oh, yeah, and a set of 15X7 Panasport racing wheels in excellent condition, Baucom body kit, FG molds for trunk lids, and small bump hoods - and more - things I will not need for the move to Vintage, can make you go fast in EP and FP.

Re: Guy Croft 3D Exhaust cam needed for Vintage build

Posted: Fri Dec 14, 2018 9:44 pm
by fp55scca
--Bill, did you try AutoRicambi? They were functioning as a GC outlet of sorts for some performance items.

--I like you shopping list! :)

Re: Guy Croft 3D Exhaust cam needed for Vintage build

Posted: Fri Dec 14, 2018 10:55 pm
by cgranju
I’d be interested in hearing about the street cams you have.

Re: Guy Croft 3D Exhaust cam needed for Vintage build

Posted: Fri Dec 14, 2018 11:00 pm
by ST3Racer
Jim,
I did try Autoricambi. I got what I will need for my engine build. I am checking out a clean, already stripped for racing chassis tomorrow. I have to move this along while its winter, to get ready for spring.

The store is open - what do you need for either fast street, or racing? Let me know. You might add to the list my complete Volumex factory kit, with custom DCOE suck-thru manifold and 45mm carbie. That set-up dynoed at 225WHP = 275 Crank HP! Juicy stuff to finance the Vintage build.

Anyone on the Forum is welcome to shop!

Re: Guy Croft 3D Exhaust cam needed for Vintage build

Posted: Fri Dec 14, 2018 11:04 pm
by ST3Racer
forgot to mention: also in the 'store' is a fresh 84.6 overbore 10.4:1, 2 liter shortblock built up with Venolias, balanced crank, and Carrillo rods! Shut the door...

Open to offers.

Re: Guy Croft 3D Exhaust cam needed for Vintage build

Posted: Fri Dec 14, 2018 11:07 pm
by ST3Racer
Chris,
A pristine set of Breda 40/80-80/40 10mm gross lift cams. Bayless/Delta A-16 inlet, PBS F2 inlet cam. PM me for more.

Re: Guy Croft 3D Exhaust cam needed for Vintage build

Posted: Wed Jan 02, 2019 11:59 am
by ward00
ST3Racer wrote:
Fri Dec 14, 2018 11:04 pm
forgot to mention: also in the 'store' is a fresh 84.6 overbore 10.4:1, 2 liter shortblock built up with Venolias, balanced crank, and Carrillo rods! Shut the door...

Open to offers.
May be interested. Could you PM me with contact info to discuss.